| Poster | Thread |
 thinkchip
|  |
A1/500 default nvram
Posted on 5-May-2012 4:13:19
| | [ #1 ] |
|
|
 |
Super Member
 |
Joined: 26-Mar-2004
Posts: 1185
From: Salt Lake City, Utah, USA | | |
|
| I've had some problems with my SAM 460. It's like some hidden settings are locked into NVRAM. I'm wondering how to go about setting NVRAM to it's default state. _________________
X5000 / microA1(OS4.1 FE U2) / CodeBench / Imagine / Blender
Lightwave 2019 / Microsoft Visual C++ |
|
| Status: Offline |
|
|
vox
 | |
Re: A1/500 default nvram
Posted on 5-May-2012 13:44:13
| | [ #2 ] |
|
|
 |
Elite Member
 |
Joined: 12-Jun-2005
Posts: 3957
From: Belgrade, Serbia | | |
|
| |
| Status: Offline |
|
|
Spectre660
 | |
Re: A1/500 default nvram
Posted on 5-May-2012 14:29:19
| | [ #3 ] |
|
|
 |
Elite Member
|
Joined: 4-Jun-2005
Posts: 3918
From: Unknown | | |
|
| @thinkchip
don't know how to resets but these seem to be the default Uboot Settings.
As posted by Metalhart before starting to adjust .
baudrate=115200
loads_echo=1
hostname=Sam460ex
stdout=vga
stdin=usbkbd
hush=0
ide_doreset=on
ide_reset_timeout=15
ide_cd_timeout=20
pcie_mode=RP:RP
pciconfighost=1
ipaddr=192.168.2.50
serverip=192.168.2.222
video_activate=pci
boota_timeout=2
bootcmd=menu; run menuboot_cmd
menucmd=menu
boot_method=boota
boot1=ssiicdrom
usb_enable_4x0=1
usb_retry=1
usb_ohci_power_down_before_reset=1
scan_usb_storage=1
ethact=ppc_4xx_eth0
ethaddr=00:50:C2:80:D4:B6
menuboot_cmd=boota
menuboot_delay=2
os4_commandline=debuglevel=0
bootargs=root=/dev/sda3 console=tty0
ver=U-Boot 2010.06.03 (Jan 24 2011 - 12:07:20)
_________________
Sam460ex : Radeon Rx550 Single slot Video Card : SIL3112 SATA card |
|
| Status: Offline |
|
|
thinkchip
| |
Re: A1/500 default nvram
Posted on 20-May-2012 2:49:49
| | [ #4 ] |
|
|
|
Super Member
|
Joined: 26-Mar-2004
Posts: 1185
From: Salt Lake City, Utah, USA | | |
|
| @vox
I created the boot disk from the iso file. Then I tried reflashing uboot. Everything seemed to go okay at first. Erasing went okay, but rewriting failed with error 1. Does anybody know what error 1 is? Now it won't boot up of course. Last edited by thinkchip on 20-May-2012 at 02:50 AM.
_________________
X5000 / microA1(OS4.1 FE U2) / CodeBench / Imagine / Blender
Lightwave 2019 / Microsoft Visual C++ |
|
| Status: Offline |
|
|
vox
| |
Re: A1/500 default nvram
Posted on 20-May-2012 22:07:07
| | [ #5 ] |
|
|
|
Elite Member
|
Joined: 12-Jun-2005
Posts: 3957
From: Belgrade, Serbia | | |
|
| @thinkchip
Quote:
| I created the boot disk from the iso file. Then I tried reflashing uboot. Everything seemed to go okay at first. Erasing went okay, but rewriting failed with error 1. Does anybody know what error 1 is? Now it won't boot up of course. Last edited by thinkchip on 20-May-2012 at 03:50 AM. |
Very sad to hear about it. There are no error codes mentioned.
WARNING!
Upgrading the Sam460ex firmware is potentially dangerous.
If something should go wrong during the update, it might leave your system unusable.
In case this should happen, send an email to the following address:
support@acube-systems.com
and ask for help on how to solve the probl
Please refer to Acube support to get the proper flash or solution._________________
OS 3.x AROS and MOS supporter, fi di good, nothing fi di unprofessionalism. Learn it harder way!
SinclairQL and WII U lover :D
YT http://www.youtube.com/user/rasvoja |
|
| Status: Offline |
|
|
thinkchip
| |
Re: A1/500 default nvram
Posted on 23-May-2012 13:49:52
| | [ #6 ] |
|
|
|
Super Member
|
Joined: 26-Mar-2004
Posts: 1185
From: Salt Lake City, Utah, USA | | |
|
| @vox
Acube is sending me a flashed eprom. It could be the power supply is causing problems. Acube has been very helpful during my problems. They also sent a new 2- GB RAM module Last edited by thinkchip on 23-May-2012 at 01:50 PM.
_________________
X5000 / microA1(OS4.1 FE U2) / CodeBench / Imagine / Blender
Lightwave 2019 / Microsoft Visual C++ |
|
| Status: Offline |
|
|
22 crawler(s) on-line.
95 guest(s) on-line.
0 member(s) on-line.
