@ghillo

Quote:

ghillo wrote: @Geri Sorry I also can not understand this delay so long to load the kernel image, maybe it could be a problem in the management of SATA? Or some parameter of UBoot? Then I'm using both the integrated PATA and the Sil3112. On the PATA I have 2 HD, 1 CD burner and 1 DVD burner. On SATA 1 HD 320Gb with OS4.1 and Linux installed. My A1g3XE has been fixed with DMA and USB correction.

I could imagine that there is a conflict between the PATA and the SATA controller. It would be worth a try to just disable DMA for the CD/DVD drives (with libata.dma=1).

BTW: How much memory to you have in your A1XE? If you use two registered SDRAM DIMMs than it would be a good idea to limit the available memory to one DIMM only.

_________________
A1SE: G3@600MHz, 2GB, 1GBit network card
A1XE: G4@933MHz, 2GB, refitted AC'97 codec
microA1: G3@800MHz, 1GB

- A1 Linux support -

@Geri

I installed a single 1Gb sdram module on my A1.
So from what I understand libata.dma = 1 disables the dma for PATA devices? I thought that deactivated the dma with the value at 0.

@ghillo

Quote:

ghillo wrote: @Geri I installed a single 1Gb sdram module on my A1.

Okay, then it should not be a problem. But then I wonder what could cause this problems. Do you use any USB devices with the onboard USB controller?

Quote:

So from what I understand libata.dma = 1 disables the dma for PATA devices? I thought that deactivated the dma with the value at 0.

No and yes. It leaves DMA enabled only for harddisks, but disables it for CD/DVD drives. See here. Otherwise we could still try to disable DMA only for the PATA controller using multiple libata.force parameters.

_________________
A1SE: G3@600MHz, 2GB, 1GBit network card
A1XE: G4@933MHz, 2GB, refitted AC'97 codec
microA1: G3@800MHz, 1GB

- A1 Linux support -

@Geri

I have a PCI card with USB2.0 to which I connected a front panel with a USB, an SD / MMC memory card reader etc.
On the integrated controller of the A1 I have USB HUB with 4 ports

As for libatadma I understood, however I had to disable all devices in DMA during the installation otherwise the installation CD would not start and the system would crash.

@ghillo

Quote:

ghillo wrote: @Geri I have a PCI card with USB2.0 to which I connected a front panel with a USB, an SD / MMC memory card reader etc. On the integrated controller of the A1 I have USB HUB with 4 ports As for libatadma I understood, however I had to disable all devices in DMA during the installation otherwise the installation CD would not start and the system would crash.

I always had DMA activated with the sii3114 SATA controller and the onboard IDE controller. So I wonder what the difference could be with your A1XE.

Can you send me the content of /proc/cpuinfo and the output of the dmesg command?

_________________
A1SE: G3@600MHz, 2GB, 1GBit network card
A1XE: G4@933MHz, 2GB, refitted AC'97 codec
microA1: G3@800MHz, 1GB

- A1 Linux support -

@ghillo

Quote:

Ho provato a vedere cosa c'è nella partizione di boot ed è così composta:

Che cosa?

Quote:

Ma le immagini del kernel non dovrebbero essere nella partizione di boot?

La partizione di avvio è dove devono essere le immagini del kernel, dal momento che il kernel viene caricato all'avvio.

Quote:

Non dovrebbero esserci anche i moduli del kernel (mi ricordo che c'erano nelle versioni precedenti che avevo installato sul mio A1)?

Non nella partizione di avvio, ma memorizzata nella partizione di root nel posto standard.

@Geri

Quote:

I'm not sure if Hypex understands Italian, but let's see if I remember some of the Italian I learned at school.

Que?

No, but Google Translate is my friend.

@ghillo

Quote:

So from what I understand libata.dma = 1 disables the dma for PATA devices? I thought that deactivated the dma with the value at 0.

I thought I also put in DMA "All, HD, CD, Off" options so people could avoid meaningless numbers.

Quote:

I have a PCI card with USB2.0 to which I connected a front panel with a USB, an SD / MMC memory card reader etc.

Same here.

Quote:

On the integrated controller of the A1 I have USB HUB with 4 ports

I tested a good quality hub with my A1 but it didn't work in UBoot. My internal ports are unfixed. But I found I could plug in/out SanDisk USB sticks and UBoot detected them directly in the port. So this A1 USB detection problem must be device dependant. Most devices didn't work I suppose.

Quote:

As for libatadma I understood, however I had to disable all devices in DMA during the installation otherwise the installation CD would not start and the system would crash.

Then you have a DMA problem. It usually indicates an unfixed board. I've seen this happen before with CD reads failing in the installer. A reboot with DMA off fixed it. However, it should have been fine with DMA on SATA, as it is with DMA on my 0680 IDE. My A1 is unfixed. But if your boot volume was on PATA connected to onboard IDE, on an unfixed board, only then should you need to disable DMA.

Did you get your A1 "fixed" or buy it that way with DMA?

And does it work fine with DMA enabled on OS4? You can run UBoot Prefs from OS4 and check the DMA settings from the HDD section. Or check from UBoot/OS4 Shell the UBoot variables for those whol like it technical.

Last edited by Hypex on 25-Oct-2018 at 05:07 PM.
Last edited by Hypex on 25-Oct-2018 at 05:02 PM.

Quote:

No, but Google Translate is my friend.

Traductor de Google es mi amiga tambien.


Note: there should be a diacritic over the 'e' in 'tambien', but this triggers the "blank message" bug in the forum software.

_________________
"Unix is supposed to fix that." -- Jay Miner

@Hypex

Quote:

Hypex wrote: @ghillo Quote: So from what I understand libata.dma = 1 disables the dma for PATA devices? I thought that deactivated the dma with the value at 0. I thought I also put in DMA "All, HD, CD, Off" options so people could avoid meaningless numbers. Quote: I have a PCI card with USB2.0 to which I connected a front panel with a USB, an SD / MMC memory card reader etc. Same here. Quote: On the integrated controller of the A1 I have USB HUB with 4 ports I tested a good quality hub with my A1 but it didn't work in UBoot. My internal ports are unfixed. But I found I could plug in/out SanDisk USB sticks and UBoot detected them directly in the port. So this A1 USB detection problem must be device dependant. Most devices didn't work I suppose. Quote: As for libatadma I understood, however I had to disable all devices in DMA during the installation otherwise the installation CD would not start and the system would crash. Then you have a DMA problem. It usually indicates an unfixed board. I've seen this happen before with CD reads failing in the installer. A reboot with DMA off fixed it. However, it should have been fine with DMA on SATA, as it is with DMA on my 0680 IDE. My A1 is unfixed. But if your boot volume was on PATA connected to onboard IDE, on an unfixed board, only then should you need to disable DMA. Did you get your A1 "fixed" or buy it that way with DMA? And does it work fine with DMA enabled on OS4? You can run UBoot Prefs from OS4 and check the DMA settings from the HDD section. Or check from UBoot/OS4 Shell the UBoot variables for those whol like it technical.

My A1 is fixed both DMA and USB side. Using OS4 I have all the devices that work with DMA and do not give problems.
Could it be like I've patched up Linux partitions? Both the boot and the root have these values
Blocksize 512
Buffer 1000
Maxtransfer 7FFFFFFF
Mask FFFFFFFE

The same values that are set for OS4 partitions

@Hypex

I realized that in uboot I still set the old parameters to boot Linux that is:

root = / dev / hda3 video = radeon: 1024x768-8 @ 70 l2cr = 0x80000000 hdc = ide-scsi

They should not have any more effect using the SLB but you never know that they create problems.
Can I delete this line from UBoot? deleting the row from UBoot in OS4 or from the bios prompt with setevent Linux bringing it to 0?

@ghillo

Quote:

Could it be like I've patched up Linux partitions? Both the boot and the root have these values

That shouldn't affect it as those values are for AmigaOS. The DOS Type may matter but if it mounts the partition fine then those values are fine.

Quote:

Can I delete this line from UBoot? deleting the row from UBoot in OS4 or from the bios prompt with setevent Linux bringing it to 0?

You can reset or delete that if you want. The SLB will actually set it for booting Linux. It will set the bootargs variable to match your boot settings before it tells UBoot to boot it. It only affects memory.

Last edited by Hypex on 31-Oct-2018 at 06:16 AM.

@Geri

During the boot I noticed two lines at the beginning that then do not appear if I run dmesg.

init: 1: conf / conf.d / amigaos4-slb grep not found

the other line I could not write it
my cpu info is

processor : 0
cpu : 750FX
temperature : 1-76 C (uncalibrated)
clock : 800.000000MHz
revision : 2.2 (pvr 7000 0202)
bogomips : 66.66

total bogomips : 66.66
timebase : 33333333
platform : AmigaOne
model : AmigaOne
vendor : Eyetech Ltd.
Memory : 1024 MB

what brings me back to dmesg is this:

[ 0.000000] Using AmigaOne machine description
[ 0.000000] Total memory = 1024MB; using 2048kB for hash table (at cfe00000)
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.16.0-4-book3s-amigaone-smp+ (root@amigaone) (gcc version 4.9.2 (Debian 4.9.2-10) ) #3 SMP Sun Oct 18 15:18:27 CEST 2015
[ 0.000000] Found initrd at 0xcec3a000:0xcef65d5f
[ 0.000000] Found legacy serial port 0 for /pci@80000000/isa@7/serial@3f8
[ 0.000000] port=3f8, taddr=fe0003f8, irq=0, clk=1843200, speed=115200
[ 0.000000] Found legacy serial port 1 for /pci@80000000/isa@7/serial@2f8
[ 0.000000] port=2f8, taddr=fe0002f8, irq=0, clk=1843200, speed=115200
[ 0.000000] CPU maps initialized for 1 thread per core
[ 0.000000] (thread shift is 0)
[ 0.000000] bootconsole [udbg0] enabled
[ 0.000000] Adding PCI host bridge /pci@80000000
[ 0.000000] PCI host bridge /pci@80000000 (primary) ranges:
[ 0.000000] IO 0x00000000fe000000..0x00000000febfffff -> 0x0000000000000000
[ 0.000000] MEM 0x0000000080000000..0x00000000fcffffff -> 0x0000000080000000
[ 0.000000] MEM 0x00000000fd000000..0x00000000fdffffff -> 0x0000000000000000
[ 0.000000] Top of RAM: 0x40000000, Total RAM: 0x40000000
[ 0.000000] Memory hole size: 0MB
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00000000-0x2fffffff]
[ 0.000000] Normal empty
[ 0.000000] HighMem [mem 0x30000000-0x3fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x3fffffff]
[ 0.000000] On node 0 totalpages: 262144
[ 0.000000] free_area_init_node: node 0, pgdat c0768280, node_mem_map c08ec000
[ 0.000000] DMA zone: 1536 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 196608 pages, LIFO batch:31
[ 0.000000] HighMem zone: 512 pages used for memmap
[ 0.000000] HighMem zone: 65536 pages, LIFO batch:15
[ 0.000000] PERCPU: Embedded 9 pages/cpu @c10f2000 s13312 r8192 d15360 u36864
[ 0.000000] pcpu-alloc: s13312 r8192 d15360 u36864 alloc=9*4096
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260608
[ 0.000000] Kernel command line: root=UUID=6172a36a-339b-4d74-a522-538f29675a37 console=tty0 l2cr=0x80000000 video=radeonfb:off libata.dma=0 quiet
[ 0.000000] l2cr set to 80000000
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Sorting __ex_table...
[ 0.000000] Memory: 1024812K/1048576K available (5496K kernel code, 412K rwdata, 1392K rodata, 380K init, 1408K bss, 23764K reserved, 262144K highmem)
[ 0.000000] Kernel virtual memory layout:
[ 0.000000] * 0xfff9f000..0xfffff000 : fixmap
[ 0.000000] * 0xff800000..0xffc00000 : highmem PTEs
[ 0.000000] * 0xff600000..0xff800000 : consistent mem
[ 0.000000] * 0xfe9fc000..0xff600000 : early ioremap
[ 0.000000] * 0xf1000000..0xfe9fc000 : vmalloc & ioremap
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] NR_IRQS:512 nr_irqs:512 16
[ 0.000000] i8259 legacy interrupt controller initialized
[ 0.000000] time_init: decrementer frequency = 33.333333 MHz
[ 0.000000] time_init: processor frequency = 800.000000 MHz
[ 0.000025] clocksource: timebase mult[1e000005] shift[24] registered
[ 0.000041] clockevent: decrementer mult[8888887] shift[32] cpu[0]
[ 0.000466] Console: colour dummy device 80x25
[ 0.000491] console [tty0] enabled
[ 0.000499] bootconsole [udbg0] disabled
[ 0.000537] pid_max: default: 32768 minimum: 301
[ 0.000700] Security Framework initialized
[ 0.000852] AppArmor: AppArmor disabled by boot time parameter
[ 0.000860] Yama: disabled by default; enable with sysctl kernel.yama.*
[ 0.000948] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000958] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.002500] Initializing cgroup subsys memory
[ 0.002552] Initializing cgroup subsys devices
[ 0.002596] Initializing cgroup subsys freezer
[ 0.002612] Initializing cgroup subsys net_cls
[ 0.002653] Initializing cgroup subsys blkio
[ 0.002679] Initializing cgroup subsys perf_event
[ 0.002690] Initializing cgroup subsys net_prio
[ 0.002774] ftrace: allocating 17997 entries in 53 pages
[ 0.030838] Brought up 1 CPUs
[ 0.031810] devtmpfs: initialized
[ 0.035266] NET: Registered protocol family 16
[ 0.038329] PCI: Probing PCI hardware
[ 0.038515] PCI host bridge to bus 0000:00
[ 0.038539] pci_bus 0000:00: root bus resource [io 0x0000-0xbfffff]
[ 0.038550] pci_bus 0000:00: root bus resource [mem 0x80000000-0xfcffffff]
[ 0.038562] pci_bus 0000:00: root bus resource [mem 0xfd000000-0xfdffffff] (bus address [0x00000000-0x00ffffff])
[ 0.038578] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.038594] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to ff
[ 0.038606] pci_bus 0000:00: scanning bus
[ 0.038675] pci 0000:00:00.0: [10cc:0660] type 00 class 0x060000
[ 0.038714] pci 0000:00:00.0: calling quirk_mmio_always_on+0x0/0x34
[ 0.038740] pci 0000:00:00.0: reg 0x10: [mem 0xfd000000-0xfd3fffff pref]
[ 0.038780] pci 0000:00:00.0: calling pcibios_fixup_resources+0x0/0x1c4
[ 0.039018] pci 0000:00:01.0: [10cc:0661] type 01 class 0x060400
[ 0.039050] pci 0000:00:01.0: calling pcibios_fixup_resources+0x0/0x1c4
[ 0.039243] pci 0000:00:06.0: [10b7:9200] type 00 class 0x020000
[ 0.039265] pci 0000:00:06.0: reg 0x10: [io 0x802000-0x80207f]
[ 0.039279] pci 0000:00:06.0: reg 0x14: [mem 0x98100000-0x9810007f]
[ 0.039311] pci 0000:00:06.0: reg 0x30: [mem 0xfd000000-0xfd01ffff pref]
[ 0.039326] pci 0000:00:06.0: calling pcibios_fixup_resources+0x0/0x1c4
[ 0.039355] pci 0000:00:06.0: supports D1 D2
[ 0.039365] pci 0000:00:06.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.039379] pci 0000:00:06.0: PME# disabled
[ 0.039591] pci 0000:00:07.0: [1106:0686] type 00 class 0x060100
[ 0.039646] pci 0000:00:07.0: calling pcibios_fixup_resources+0x0/0x1c4
[ 0.039665] pci 0000:00:07.0: calling quirk_via_bridge+0x0/0xec
[ 0.039860] pci 0000:00:07.1: [1106:0571] type 00 class 0x01018a
[ 0.039876] pci 0000:00:07.1: calling quirk_no_ata_d3+0x0/0x34
[ 0.039913] pci 0000:00:07.1: reg 0x20: [io 0xcc00-0xcc0f]
[ 0.039935] pci 0000:00:07.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7]
[ 0.039944] pci 0000:00:07.1: legacy IDE quirk: reg 0x14: [io 0x03f6]
[ 0.039953] pci 0000:00:07.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177]
[ 0.039961] pci 0000:00:07.1: legacy IDE quirk: reg 0x1c: [io 0x0376]
[ 0.039973] pci 0000:00:07.1: calling pcibios_fixup_resources+0x0/0x1c4
[ 0.040170] pci 0000:00:07.2: [1106:3038] type 00 class 0x0c0300
[ 0.040209] pci 0000:00:07.2: reg 0x20: [io 0x802080-0x80209f]
[ 0.040232] pci 0000:00:07.2: calling pcibios_fixup_resources+0x0/0x1c4
[ 0.040423] pci 0000:00:07.3: [1106:3038] type 00 class 0x0c0300
[ 0.040518] pci 0000:00:07.3: reg 0x20: [io 0x8020a0-0x8020bf]
[ 0.040543] pci 0000:00:07.3: calling pcibios_fixup_resources+0x0/0x1c4
[ 0.040767] pci 0000:00:07.4: [1106:3057] type 00 class 0x000000
[ 0.040796] pci 0000:00:07.4: calling quirk_vt82c686_acpi_iobases+0x0/0x170
[ 0.040849] pci 0000:00:07.4: calling pcibios_fixup_resources+0x0/0x1c4
[ 0.040862] pci 0000:00:07.4: calling quirk_via_acpi+0x0/0x5c
[ 0.040877] pci 0000:00:07.4: calling quirk_vt82c686_acpi+0x0/0x8c
[ 0.040896] pci 0000:00:07.4: quirk: [io 0x6000-0x607f] claimed by vt82c686 HW-mon
[ 0.040907] pci 0000:00:07.4: quirk: [io 0x5000-0x500f] claimed by vt82c686 SMB
[ 0.041116] pci 0000:00:07.5: [1106:3058] type 00 class 0x040100
[ 0.041133] pci 0000:00:07.5: calling quirk_vt82c686_sound_iobases+0x0/0x8c
[ 0.041154] pci 0000:00:07.5: reg 0x10: [io 0xdc00-0xdcff]
[ 0.041168] pci 0000:00:07.5: reg 0x14: [io 0xe000-0xe003]
[ 0.041182] pci 0000:00:07.5: reg 0x18: [io 0x0330-0x0333]
[ 0.041215] pci 0000:00:07.5: calling pcibios_fixup_resources+0x0/0x1c4
[ 0.041412] pci 0000:00:07.6: [1106:3068] type 00 class 0x078000
[ 0.041428] pci 0000:00:07.6: calling quirk_vt82c686_modem_iobases+0x0/0x74
[ 0.041448] pci 0000:00:07.6: reg 0x10: [io 0xe400-0xe4ff]
[ 0.041492] pci 0000:00:07.6: calling pcibios_fixup_resources+0x0/0x1c4
[ 0.041693] pci 0000:00:08.0: [104c:8024] type 00 class 0x0c0010
[ 0.041715] pci 0000:00:08.0: reg 0x10: [mem 0x98100800-0x98100fff]
[ 0.041729] pci 0000:00:08.0: reg 0x14: [mem 0x98104000-0x98107fff]
[ 0.041769] pci 0000:00:08.0: calling pcibios_fixup_resources+0x0/0x1c4
[ 0.041797] pci 0000:00:08.0: supports D1 D2
[ 0.041805] pci 0000:00:08.0: PME# supported from D0 D1 D2 D3hot
[ 0.041816] pci 0000:00:08.0: PME# disabled
[ 0.042023] pci 0000:00:09.0: [1033:0035] type 00 class 0x0c0310
[ 0.042045] pci 0000:00:09.0: reg 0x10: [mem 0x98108000-0x98108fff]
[ 0.042086] pci 0000:00:09.0: calling pcibios_fixup_resources+0x0/0x1c4
[ 0.042113] pci 0000:00:09.0: supports D1 D2
[ 0.042122] pci 0000:00:09.0: PME# supported from D0 D1 D2 D3hot
[ 0.042131] pci 0000:00:09.0: PME# disabled
[ 0.042344] pci 0000:00:09.1: [1033:0035] type 00 class 0x0c0310
[ 0.042366] pci 0000:00:09.1: reg 0x10: [mem 0x98109000-0x98109fff]
[ 0.042408] pci 0000:00:09.1: calling pcibios_fixup_resources+0x0/0x1c4
[ 0.042435] pci 0000:00:09.1: supports D1 D2
[ 0.042444] pci 0000:00:09.1: PME# supported from D0 D1 D2 D3hot
[ 0.042453] pci 0000:00:09.1: PME# disabled
[ 0.042662] pci 0000:00:09.2: [1033:00e0] type 00 class 0x0c0320
[ 0.042683] pci 0000:00:09.2: reg 0x10: [mem 0x9810a000-0x9810a0ff]
[ 0.042724] pci 0000:00:09.2: calling pcibios_fixup_resources+0x0/0x1c4
[ 0.042751] pci 0000:00:09.2: supports D1 D2
[ 0.042760] pci 0000:00:09.2: PME# supported from D0 D1 D2 D3hot
[ 0.042769] pci 0000:00:09.2: PME# disabled
[ 0.042977] pci 0000:00:0a.0: [1095:3112] type 00 class 0x010400
[ 0.042998] pci 0000:00:0a.0: reg 0x10: [io 0x802400-0x802407]
[ 0.043011] pci 0000:00:0a.0: reg 0x14: [io 0x802408-0x80240b]
[ 0.043025] pci 0000:00:0a.0: reg 0x18: [io 0x802410-0x802417]
[ 0.043039] pci 0000:00:0a.0: reg 0x1c: [io 0x802418-0x80241b]
[ 0.043052] pci 0000:00:0a.0: reg 0x20: [io 0x802420-0x80242f]
[ 0.043066] pci 0000:00:0a.0: reg 0x24: [mem 0x9810a200-0x9810a3ff]
[ 0.043080] pci 0000:00:0a.0: reg 0x30: [mem 0xfd000000-0xfd07ffff pref]
[ 0.043095] pci 0000:00:0a.0: calling pcibios_fixup_resources+0x0/0x1c4
[ 0.043122] pci 0000:00:0a.0: supports D1 D2
[ 0.043302] pci_bus 0000:00: fixups for bus
[ 0.043397] pci 0000:00:01.0: scanning [bus 01-01] behind bridge, pass 0
[ 0.043533] pci_bus 0000:01: scanning bus
[ 0.043567] pci 0000:01:00.0: [1002:5960] type 00 class 0x030000
[ 0.043589] pci 0000:01:00.0: reg 0x10: [mem 0x80000000-0x87ffffff pref]
[ 0.043602] pci 0000:01:00.0: reg 0x14: [io 0x2000-0x20ff]
[ 0.043615] pci 0000:01:00.0: reg 0x18: [mem 0x88000000-0x8800ffff]
[ 0.043641] pci 0000:01:00.0: reg 0x30: [mem 0xfd000000-0xfd01ffff pref]
[ 0.043656] pci 0000:01:00.0: calling pcibios_fixup_resources+0x0/0x1c4
[ 0.043689] pci 0000:01:00.0: supports D1 D2
[ 0.043863] pci 0000:01:00.1: [1002:5940] type 00 class 0x038000
[ 0.043882] pci 0000:01:00.1: reg 0x10: [mem 0x90000000-0x97ffffff pref]
[ 0.043895] pci 0000:01:00.1: reg 0x14: [mem 0x98000000-0x9800ffff]
[ 0.043930] pci 0000:01:00.1: calling pcibios_fixup_resources+0x0/0x1c4
[ 0.043956] pci 0000:01:00.1: supports D1 D2
[ 0.044153] pci_bus 0000:01: fixups for bus
[ 0.044162] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.044177] pci 0000:00:01.0: bridge window [io 0x2000-0x2fff]
[ 0.044188] pci 0000:00:01.0: bridge window [mem 0x88000000-0x880fffff]
[ 0.044199] pci 0000:00:01.0: bridge window [mem 0x80000000-0x87ffffff pref]
[ 0.044220] pci_bus 0000:01: bus scan returning with max=01
[ 0.044234] pci 0000:00:01.0: scanning [bus 01-01] behind bridge, pass 1
[ 0.044245] pci_bus 0000:00: bus scan returning with max=01
[ 0.044255] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
[ 0.044358] PCI: Cannot allocate resource region 0 of device 0000:01:00.1, will remap
[ 0.044364] PCI: Cannot allocate resource region 1 of device 0000:01:00.1, will remap
[ 0.044414] PCI 0000:00 Cannot reserve Legacy IO [io 0x0000-0x0fff]
[ 0.044506] pci 0000:00:0a.0: BAR 6: assigned [mem 0x88100000-0x8817ffff pref]
[ 0.044519] pci 0000:00:06.0: BAR 6: assigned [mem 0x88180000-0x8819ffff pref]
[ 0.044536] pci 0000:01:00.1: BAR 0: can't assign mem pref (size 0x8000000)
[ 0.044549] pci 0000:01:00.0: BAR 6: assigned [mem 0x88020000-0x8803ffff pref]
[ 0.044559] pci 0000:01:00.1: BAR 1: assigned [mem 0x88010000-0x8801ffff]
[ 0.044572] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.044583] pci 0000:00:01.0: bridge window [io 0x2000-0x2fff]
[ 0.044594] pci 0000:00:01.0: bridge window [mem 0x88000000-0x880fffff]
[ 0.044605] pci 0000:00:01.0: bridge window [mem 0x80000000-0x87ffffff pref]
[ 0.044617] pci_bus 0000:00: Some PCI device resources are unassigned, try booting with pci=realloc
[ 0.044627] pci_bus 0000:00: resource 4 [io 0x0000-0xbfffff]
[ 0.044637] pci_bus 0000:00: resource 5 [mem 0x80000000-0xfcffffff]
[ 0.044646] pci_bus 0000:00: resource 6 [mem 0xfd000000-0xfdffffff]
[ 0.044655] pci_bus 0000:01: resource 0 [io 0x2000-0x2fff]
[ 0.044664] pci_bus 0000:01: resource 1 [mem 0x88000000-0x880fffff]
[ 0.044673] pci_bus 0000:01: resource 2 [mem 0x80000000-0x87ffffff pref]
[ 0.049802] vgaarb: setting as boot device: PCI:0000:01:00.0
[ 0.049818] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.049825] vgaarb: loaded
[ 0.049831] vgaarb: bridge control possible 0000:01:00.0
[ 0.050302] SCSI subsystem initialized
[ 0.050559] libata version 3.00 loaded.
[ 0.051831] Switched to clocksource timebase
[ 0.079314] NET: Registered protocol family 2
[ 0.080710] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.080996] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.081464] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.082008] TCP: reno registered
[ 0.082022] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.082158] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.082636] NET: Registered protocol family 1
[ 0.082823] pci 0000:00:07.2: calling quirk_usb_early_handoff+0x0/0x818
[ 0.082864] pci 0000:00:07.2: calling quirk_via_vlink+0x0/0xd8
[ 0.082912] pci 0000:00:07.3: calling quirk_usb_early_handoff+0x0/0x818
[ 0.082928] pci 0000:00:07.3: calling quirk_via_vlink+0x0/0xd8
[ 0.082971] pci 0000:00:07.4: calling quirk_vt82c686_powerup+0x0/0x214
[ 0.082988] pci 0000:00:07.4: Emitting soft resume event to power up.
[ 0.083015] pci 0000:00:07.5: calling quirk_vt82c686_sound_init+0x0/0x90
[ 0.084044] pci 0000:00:09.0: calling quirk_usb_early_handoff+0x0/0x818
[ 0.084247] pci 0000:00:09.1: calling quirk_usb_early_handoff+0x0/0x818
[ 0.084283] pci 0000:00:09.2: calling quirk_usb_early_handoff+0x0/0x818
[ 0.084317] PCI: CLS mismatch (32 != 4), using 32 bytes
[ 0.084342] pci 0000:01:00.0: calling fixup_vga+0x0/0x7c
[ 0.084764] Unpacking initramfs...
[ 2.150892] Freeing initrd memory: 3244K (cec3a000 - cef65000)
[ 2.151429] Thermal assist unit using timers, shrink_timer: 500 jiffies
[ 2.151492] irq: no irq domain found for /pci@80000000/isa@7 !
[ 2.151512] irq: no irq domain found for /pci@80000000/isa@7 !
[ 2.152834] futex hash table entries: 256 (order: 1, 8192 bytes)
[ 2.152965] audit: initializing netlink subsys (disabled)
[ 2.153152] audit: type=2000 audit(2.139:1): initialized
[ 2.154810] zbud: loaded
[ 2.155156] VFS: Disk quotas dquot_6.5.2
[ 2.155232] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 2.155402] msgmni has been set to 1497
[ 2.157383] alg: No test for stdrng (krng)
[ 2.157511] bounce: pool size: 64 pages
[ 2.157607] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 2.157865] io scheduler noop registered
[ 2.157877] io scheduler deadline registered
[ 2.158010] io scheduler cfq registered (default)
[ 2.159357] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 2.181421] serial8250.0: ttyS0 at I/O 0x3f8 (irq = 0, base_baud = 115200) is a 16550A
[ 2.202380] serial8250.0: ttyS1 at I/O 0x2f8 (irq = 0, base_baud = 115200) is a 16550A
[ 2.202798] Generic non-volatile memory driver v1.1
[ 2.202956] Linux agpgart interface v0.103
[ 2.203129] irq: no irq domain found for /pci@80000000/isa@7 !
[ 2.203142] irq: no irq domain found for /pci@80000000/isa@7 !
[ 2.203703] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.203730] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 2.204236] mousedev: PS/2 mouse device common for all mice
[ 2.205031] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0
[ 2.205089] rtc_cmos rtc_cmos: alarms up to one day, 114 bytes nvram
[ 2.205196] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.205493] TCP: cubic registered
[ 2.205577] NET: Registered protocol family 10
[ 2.206637] mip6: Mobile IPv6
[ 2.206668] NET: Registered protocol family 17
[ 2.206689] mpls_gso: MPLS GSO support
[ 2.207527] registered taskstats version 1
[ 2.208816] rtc_cmos rtc_cmos: setting system clock to 2018-10-25 22:15:00 UTC (1540505700)
[ 2.208874] PM: Hibernation image not present or could not be loaded.
[ 2.211503] Freeing unused kernel memory: 380K (c06bf000 - c071e000)
[ 2.277958] systemd-udevd[57]: starting version 215
[ 2.285180] random: systemd-udevd urandom read with 0 bits of entropy available
[ 2.361429] 3c59x: Donald Becker and others.
[ 2.361514] 0000:00:06.0: 3Com PCI 3c905C Tornado at ff1fe000.
[ 2.421256] input: PC Speaker as /devices/platform/pcspkr/input/input0
[ 2.450190] [drm] Initialized drm 1.1.0 20060810
[ 2.481585] pata_via 0000:00:07.1: version 0.3.4
[ 2.481674] pata_via 0000:00:07.1: calling quirk_via_vlink+0x0/0xd8
[ 2.491113] scsi0 : pata_via
[ 2.499237] scsi1 : pata_via
[ 2.499601] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xcc00 irq 14
[ 2.499611] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xcc08 irq 15
[ 2.499979] sata_sil 0000:00:0a.0: version 2.4
[ 2.504208] scsi2 : sata_sil
[ 2.515640] scsi3 : sata_sil
[ 2.516204] ata3: SATA max UDMA/100 mmio m512@0x9810a200 tf 0x9810a280 irq 11
[ 2.516216] ata4: SATA max UDMA/100 mmio m512@0x9810a200 tf 0x9810a2c0 irq 11
[ 2.733969] [drm] radeon kernel modesetting enabled.
[ 2.735897] [drm] initializing kernel modesetting (RV280 0x1002:0x5960 0x174B:0x0260).
[ 2.735919] [drm] Forcing AGP to PCI mode
[ 2.735946] [drm] register mmio base: 0x88000000
[ 2.735951] [drm] register mmio size: 65536
[ 2.773556] [drm] Generation 2 PCI interface, using max accessible memory
[ 2.773585] radeon 0000:01:00.0: VRAM: 128M 0x0000000080000000 - 0x0000000087FFFFFF (128M used)
[ 2.773597] radeon 0000:01:00.0: GTT: 512M 0x0000000060000000 - 0x000000007FFFFFFF
[ 2.773651] [drm] Detected VRAM RAM=128M, BAR=128M
[ 2.773658] [drm] RAM width 64bits DDR
[ 2.774020] [TTM] Zone kernel: Available graphics memory: 383656 kiB
[ 2.774030] [TTM] Zone highmem: Available graphics memory: 514728 kiB
[ 2.774036] [TTM] Initializing pool allocator
[ 2.774181] [drm] radeon: 128M of VRAM memory ready
[ 2.774189] [drm] radeon: 512M of GTT memory ready.
[ 2.774302] [drm] GART: num cpu pages 131072, num gpu pages 131072
[ 2.798007] [drm] PCI GART of 512M enabled (table at 0x000000002F380000).
[ 2.798258] radeon 0000:01:00.0: WB disabled
[ 2.798281] radeon 0000:01:00.0: fence driver on ring 0 u
[ 2.798258] radeon 0000:01:00.0: WB disabled
[ 2.798281] radeon 0000:01:00.0: fence driver on ring 0 use gpu addr 0x0000000060000000 and cpu addr 0xef08f000
[ 2.798296] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 2.798301] [drm] Driver supports precise vblank timestamp query.
[ 2.798363] [drm] radeon: irq initialized.
[ 2.798443] [drm] Loading R200 Microcode
[ 2.798656] radeon 0000:01:00.0: firmware: direct-loading firmware radeon/R200_cp.bin
[ 2.801033] [drm] radeon: ring at 0x0000000060001000
[ 2.801080] [drm] ring test succeeded in 0 usecs
[ 2.803257] [drm] ib test succeeded in 0 usecs
[ 2.806976] [drm] Radeon Display Connectors
[ 2.806990] [drm] Connector 0:
[ 2.806995] [drm] VGA-1
[ 2.807005] [drm] DDC: 0x60 0x60 0x60 0x60 0x60 0x60 0x60 0x60
[ 2.807010] [drm] Encoders:
[ 2.807016] [drm] CRT1: INTERNAL_DAC1
[ 2.807023] [drm] Connector 1:
[ 2.807027] [drm] DVI-I-1
[ 2.807032] [drm] HPD1
[ 2.807040] [drm] DDC: 0x64 0x64 0x64 0x64 0x64 0x64 0x64 0x64
[ 2.807044] [drm] Encoders:
[ 2.807049] [drm] CRT2: INTERNAL_DAC2
[ 2.807054] [drm] DFP1: INTERNAL_TMDS1
[ 2.836723] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2.879617] [drm] fb mappable at 0x80040000
[ 2.879631] [drm] vram apper at 0x80000000
[ 2.879636] [drm] size 5242880
[ 2.879641] [drm] fb depth is 24
[ 2.879646] [drm] pitch is 5120
[ 2.933044] Console: switching to colour frame buffer device 160x64
[ 2.983517] radeon 0000:01:00.0: fb0: radeondrmfb frame buffer device
[ 2.983526] radeon 0000:01:00.0: registered panic notifier
[ 2.983568] [drm] Initialized radeon 2.39.0 20080528 for 0000:01:00.0 on minor 0
[ 3.013102] ata3.00: ATA-8: ST3250318AS, CC38, max UDMA/133
[ 3.013132] ata3.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 3.022781] ata3.00: configured for PIO4
[ 3.039177] ata1.00: ATA-8: WDC WD1600AVJB-63J5A0, 01.03E01, max UDMA/133
[ 3.039188] ata1.00: 312581808 sectors, multi 16: LBA48
[ 3.039212] ata1.01: ATAPI: HL-DT-ST GCE-8481B, 1.01, max UDMA/33
[ 3.039228] ata1.00: limited to UDMA/33 due to 40-wire cable
[ 3.052801] ata1.00: configured for PIO4
[ 3.053342] ata1.01: configured for PIO4
[ 3.054261] scsi 0:0:0:0: Direct-Access ATA WDC WD1600AVJB-6 3E01 PQ: 0 ANSI: 5
[ 3.057036] scsi 0:0:1:0: CD-ROM HL-DT-ST CD-RW GCE-8481B 1.01 PQ: 0 ANSI: 5
[ 3.236325] ata2.00: ATA-5: MAXTOR 6L040J2, A93.0500, max UDMA/133
[ 3.236342] ata2.00: 78177792 sectors, multi 0: LBA
[ 3.236365] ata2.01: ATAPI: TSSTcorp CDDVDW SH-S222A, SB02, max UDMA/66
[ 3.236381] ata2.00: limited to UDMA/33 due to 40-wire cable
[ 3.236390] ata2.01: limited to UDMA/33 due to 40-wire cable
[ 3.252313] ata2.00: configured for PIO4
[ 3.268106] ata2.01: configured for PIO4
[ 3.268871] scsi 1:0:0:0: Direct-Access ATA MAXTOR 6L040J2 0500 PQ: 0 ANSI: 5
[ 3.271296] scsi 1:0:1:0: CD-ROM TSSTcorp CDDVDW SH-S222A SB02 PQ: 0 ANSI: 5
[ 3.277640] scsi 2:0:0:0: Direct-Access ATA ST3250318AS CC38 PQ: 0 ANSI: 5
[ 3.484940] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 3.595852] ata4: SATA link down (SStatus 0 SControl 310)
[ 3.652473] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 3.652715] sd 0:0:0:0: [sda] Write Protect is off
[ 3.652728] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.652820] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.655387] sd 1:0:0:0: [sdb] 78177792 512-byte logical blocks: (40.0 GB/37.2 GiB)
[ 3.655602] sd 1:0:0:0: [sdb] Write Protect is off
[ 3.655615] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 3.655702] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.658576] sd 2:0:0:0: [sdc] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[ 3.658798] sd 2:0:0:0: [sdc] Write Protect is off
[ 3.658810] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 3.658900] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.663240] sdb: RDSK (512) sdb1 (EXT^C)(res 2 spb 1)
[ 3.666095] sda: RDSK (512) sda1 (SFS^B)(res 2 spb 1)
[ 3.667267] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.669223] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 3.679279] sdc: RDSK (512) sdc1 (SFS^@)(res 2 spb 1) sdc2 (LNX^@)(res 2 spb 1) sdc3 (SFS^B)(res 2 spb 1) sdc4 (SWAP)(res 2 spb 8) sdc5 (LNX^@)(res 2 spb 1) sdc6 (SWP^@)(res 2 spb 1)
[ 3.681734] sd 2:0:0:0: [sdc] Attached SCSI disk
[ 4.495892] random: nonblocking pool is initialized
[ 5.545159] input: ImPS/2 Logitech Wheel Mouse as /devices/platform/i8042/serio1/input/input3
[ 5.661114] floppy0: nodma=1
[ 5.662916] Floppy drive(s): fd0 is 2.88M
[ 5.679206] FDC 0 is a post-1991 82077
[ 5.766345] device-mapper: uevent: version 1.0.3
[ 5.768719] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com
[ 6.583487] EXT4-fs (sdc5): mounted filesystem with ordered data mode. Opts: (null)
[ 8.066877] systemd[1]: systemd 215 running in system mode. (+PAM +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ -SECCOMP -APPARMOR)
[ 8.067284] systemd[1]: Detected architecture 'ppc'.
[ 8.398109] systemd[1]: Inserted module 'autofs4'
[ 8.412462] systemd[1]: Set hostname to .
[ 10.134462] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[ 10.135023] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 10.135117] systemd[1]: Starting Remote File Systems (Pre).
[ 10.135293] systemd[1]: Reached target Remote File Systems (Pre).
[ 10.135398] systemd[1]: Starting Encrypted Volumes.
[ 10.135469] systemd[1]: Reached target Encrypted Volumes.
[ 10.135617] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[ 10.136466] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 10.136597] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[ 10.136817] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 10.136887] systemd[1]: Expecting device dev-disk-by\x2duuid-7f6f1fe9\x2d1054\x2d42e1\x2d999c\x2d6587d245968f.device...
[ 10.136958] systemd[1]: Expecting device dev-disk-by\x2duuid-4f4a2549\x2d88b3\x2d4571\x2d882a\x2dcb62562ef899.device...
[ 10.137014] systemd[1]: Starting Root Slice.
[ 10.137262] systemd[1]: Created slice Root Slice.
[ 10.137322] systemd[1]: Starting Delayed Shutdown Socket.
[ 10.137542] systemd[1]: Listening on Delayed Shutdown Socket.
[ 10.137602] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[ 10.137793] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 10.137847] systemd[1]: Starting Journal Socket (/dev/log).
[ 10.138026] systemd[1]: Listening on Journal Socket (/dev/log).
[ 10.138090] systemd[1]: Starting User and Session Slice.
[ 10.138361] systemd[1]: Created slice User and Session Slice.
[ 10.138450] systemd[1]: Starting udev Control Socket.
[ 10.138599] systemd[1]: Listening on udev Control Socket.
[ 10.138676] systemd[1]: Starting udev Kernel Socket.
[ 10.138824] systemd[1]: Listening on udev Kernel Socket.
[ 10.138913] systemd[1]: Starting Journal Socket.
[ 10.139128] systemd[1]: Listening on Journal Socket.
[ 10.139262] systemd[1]: Starting System Slice.
[ 10.139507] systemd[1]: Created slice System Slice.
[ 10.139583] systemd[1]: Starting system-systemd\x2dfsck.slice.
[ 10.140093] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[ 10.140260] systemd[1]: Starting Increase datagram queue length...
[ 10.144316] systemd[1]: Mounting POSIX Message Queue File System...
[ 10.156991] systemd[1]: Mounting Debug File System...
[ 10.171642] systemd[1]: Starting udev Coldplug all Devices...
[ 10.183720] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[ 10.207062] systemd[1]: Mounted Huge Pages File System.
[ 10.258034] systemd[1]: Starting Load Kernel Modules...
[ 10.265977] systemd[1]: Started Set Up Additional Binary Formats.
[ 10.266346] systemd[1]: Starting system-getty.slice.
[ 10.266910] systemd[1]: Created slice system-getty.slice.
[ 10.267131] systemd[1]: Started File System Check on Root Device.
[ 10.267251] systemd[1]: Starting Slices.
[ 10.267313] systemd[1]: Reached target Slices.
[ 10.656715] systemd[1]: Started Create list of required static device nodes for the current kernel.
[ 10.659352] systemd[1]: Starting Create Static Device Nodes in /dev...
[ 11.061281] systemd[1]: Started Increase datagram queue length.
[ 11.068335] systemd[1]: Mounted POSIX Message Queue File System.
[ 11.069441] systemd[1]: Mounted Debug File System.
[ 11.250661] systemd[1]: Started udev Coldplug all Devices.
[ 11.333907] systemd[1]: Starting Syslog Socket.
[ 11.360295] systemd[1]: Listening on Syslog Socket.
[ 11.360501] systemd[1]: Starting Journal Service...
[ 11.373381] systemd[1]: Started Journal Service.
[ 11.656749] lp: driver loaded but no devices found
[ 11.705597] parport_pc: VIA 686A/8231 detected
[ 11.705619] parport_pc: probing current configuration
[ 11.705649] parport_pc: Current parallel port base: 0x378
[ 11.705727] parport0: PC-style at 0x378 [PCSPP,TRISTATE,EPP]
[ 11.820536] lp0: using parport0 (polling).
[ 11.820571] parport_pc: VIA parallel port: io=0x378
[ 11.941108] fuse init (API version 7.23)
[ 12.169393] systemd-udevd[203]: starting version 215
[ 15.189827] sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
[ 15.189865] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 15.190656] sr 0:0:1:0: Attached scsi CD-ROM sr0
[ 15.247951] sr1: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 15.248933] sr 1:0:1:0: Attached scsi CD-ROM sr1
[ 15.407921] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 15.408219] sr 0:0:1:0: Attached scsi generic sg1 type 5
[ 15.411365] sd 1:0:0:0: Attached scsi generic sg2 type 0
[ 15.411646] sr 1:0:1:0: Attached scsi generic sg3 type 5
[ 15.414955] sd 2:0:0:0: Attached scsi generic sg4 type 0
[ 15.510791] snd_via82xx_modem 0000:00:07.6: calling quirk_via_vlink+0x0/0xd8
[ 15.513242] snd_via82xx_modem 0000:00:07.6: enabling bus mastering
[ 15.555803] usbcore: registered new interface driver usbfs
[ 15.556576] usbcore: registered new interface driver hub
[ 15.556856] usbcore: registered new device driver usb
[ 15.733225] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 15.894555] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 15.919523] uhci_hcd: USB Universal Host Controller Interface driver
[ 15.922530] ehci-pci: EHCI PCI platform driver
[ 16.040774] snd_via82xx_modem 0000:00:07.6: AC'97 1 access is not valid [0xffffffff], removing mixer.
[ 16.041762] snd_via82xx_modem: probe of 0000:00:07.6 failed with error -5
[ 16.096069] firewire_ohci 0000:00:08.0: added OHCI v1.10 device as card 0, 4 IR + 8 IT contexts, quirks 0x2
[ 16.097136] snd_via82xx 0000:00:07.5: calling quirk_via_vlink+0x0/0xd8
[ 16.097332] snd_via82xx 0000:00:07.5: enabling bus mastering
[ 16.604461] firewire_core 0000:00:08.0: created device fw0: GUID 0000000000028842, S400
[ 16.753133] ehci-pci 0000:00:09.2: enabling bus mastering
[ 16.753208] ehci-pci 0000:00:09.2: EHCI Host Controller
[ 16.753243] ehci-pci 0000:00:09.2: new USB bus registered, assigned bus number 1
[ 16.753489] ehci-pci 0000:00:09.2: enabling Mem-Wr-Inval
[ 16.753537] ehci-pci 0000:00:09.2: irq 7, io mem 0x9810a000
[ 16.764036] ehci-pci 0000:00:09.2: USB 2.0 started, EHCI 1.00
[ 16.764475] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 16.764487] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 16.764496] usb usb1: Product: EHCI Host Controller
[ 16.764504] usb usb1: Manufacturer: Linux 3.16.0-4-book3s-amigaone-smp+ ehci_hcd
[ 16.764513] usb usb1: SerialNumber: 0000:00:09.2
[ 16.765332] hub 1-0:1.0: USB hub found
[ 16.765379] hub 1-0:1.0: 5 ports detected
[ 16.766454] uhci_hcd 0000:00:07.2: calling quirk_via_vlink+0x0/0xd8
[ 16.766504] uhci_hcd 0000:00:07.2: enabling bus mastering
[ 16.766518] uhci_hcd 0000:00:07.2: UHCI Host Controller
[ 16.766549] uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 2
[ 16.766584] uhci_hcd 0000:00:07.2: detected 2 ports
[ 16.766649] uhci_hcd 0000:00:07.2: irq 5, io base 0x00802080
[ 16.767274] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 16.767284] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 16.767293] usb usb2: Product: UHCI Host Controller
[ 16.767302] usb usb2: Manufacturer: Linux 3.16.0-4-book3s-amigaone-smp+ uhci_hcd
[ 16.767310] usb usb2: SerialNumber: 0000:00:07.2
[ 16.768039] hub 2-0:1.0: USB hub found
[ 16.768080] hub 2-0:1.0: 2 ports detected
[ 16.768656] uhci_hcd 0000:00:07.3: calling quirk_via_vlink+0x0/0xd8
[ 16.768689] uhci_hcd 0000:00:07.3: enabling bus mastering
[ 16.768700] uhci_hcd 0000:00:07.3: UHCI Host Controller
[ 16.768726] uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 3
[ 16.768747] uhci_hcd 0000:00:07.3: detected 2 ports
[ 16.768785] uhci_hcd 0000:00:07.3: irq 5, io base 0x008020a0
[ 16.769326] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 16.769336] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 16.769345] usb usb3: Product: UHCI Host Controller
[ 16.769353] usb usb3: Manufacturer: Linux 3.16.0-4-book3s-amigaone-smp+ uhci_hcd
[ 16.769362] usb usb3: SerialNumber: 0000:00:07.3
[ 16.772582] hub 3-0:1.0: USB hub found
[ 16.772659] hub 3-0:1.0: 2 ports detected
[ 16.791337] ohci-pci: OHCI PCI platform driver
[ 16.791546] ohci-pci 0000:00:09.0: enabling bus mastering
[ 16.791565] ohci-pci 0000:00:09.0: OHCI PCI host controller
[ 16.791602] ohci-pci 0000:00:09.0: new USB bus registered, assigned bus number 4
[ 16.796027] ohci-pci 0000:00:09.0: irq 10, io mem 0x98108000
[ 17.007972] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 17.008002] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 17.008011] usb usb4: Product: OHCI PCI host controller
[ 17.008019] usb usb4: Manufacturer: Linux 3.16.0-4-book3s-amigaone-smp+ ohci_hcd
[ 17.008028] usb usb4: SerialNumber: 0000:00:09.0
[ 17.012226] hub 4-0:1.0: USB hub found
[ 17.015936] hub 4-0:1.0: 3 ports detected
[ 17.028551] ohci-pci 0000:00:09.1: enabling bus mastering
[ 17.028587] ohci-pci 0000:00:09.1: OHCI PCI host controller
[ 17.028620] ohci-pci 0000:00:09.1: new USB bus registered, assigned bus number 5
[ 17.028805] ohci-pci 0000:00:09.1: irq 11, io mem 0x98109000
[ 17.115954] usb 1-4: new high-speed USB device number 2 using ehci-pci
[ 17.357074] usb 1-4: New USB device found, idVendor=05e3, idProduct=0608
[ 17.357109] usb 1-4: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 17.357118] usb 1-4: Product: USB2.0 Hub
[ 17.377504] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 17.379421] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 17.379432] usb usb5: Product: OHCI PCI host controller
[ 17.379440] usb usb5: Manufacturer: Linux 3.16.0-4-book3s-amigaone-smp+ ohci_hcd
[ 17.379449] usb usb5: SerialNumber: 0000:00:09.1
[ 17.414000] hub 5-0:1.0: USB hub found
[ 17.414061] hub 5-0:1.0: 2 ports detected
[ 17.420560] hub 1-4:1.0: USB hub found
[ 17.424057] hub 1-4:1.0: 4 ports detected
[ 17.547310] usb 1-5: new high-speed USB device number 3 using ehci-pci
[ 17.624318] EXT4-fs (sdc5): re-mounted. Opts: errors=remount-ro
[ 17.680853] usb 1-5: New USB device found, idVendor=058f, idProduct=6362
[ 17.680886] usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 17.680895] usb 1-5: Product: Mass Storage Device
[ 17.680903] usb 1-5: Manufacturer: Generic
[ 17.680912] usb 1-5: SerialNumber: 058F312D81B1
[ 20.639038] usb-storage 1-5:1.0: USB Mass Storage device detected
[ 20.639606] scsi4 : usb-storage 1-5:1.0
[ 20.640190] usbcore: registered new interface driver usb-storage
[ 20.834799] usbcore: registered new interface driver uas
[ 21.602628] Adding 2096684k swap on /dev/sdc6. Priority:-1 extents:1 across:2096684k FS
[ 21.649424] scsi 4:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
[ 21.650592] scsi 4:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
[ 21.651628] scsi 4:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
[ 21.652620] scsi 4:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
[ 21.661138] sd 4:0:0:0: [sdd] Attached SCSI removable disk
[ 21.662466] sd 4:0:0:0: Attached scsi generic sg5 type 0
[ 21.670204] sd 4:0:0:1: [sde] Attached SCSI removable disk
[ 21.674441] sd 4:0:0:1: Attached scsi generic sg6 type 0
[ 21.683199] sd 4:0:0:2: [sdf] Attached SCSI removable disk
[ 21.711702] sd 4:0:0:2: Attached scsi generic sg7 type 0
[ 21.721038] sd 4:0:0:3: Attached scsi generic sg8 type 0
[ 21.721184] sd 4:0:0:3: [sdg] Attached SCSI removable disk
[ 23.405925] EXT4-fs (sdc2): mounting ext2 file system using the ext4 subsystem
[ 23.483620] EXT4-fs (sdc2): mounted filesystem without journal. Opts: (null)
[ 23.662701] systemd-journald[201]: Received request to flush runtime journal from PID 1
[ 25.105737] eth0: setting full-duplex.
[ 28.067420] RPC: Registered named UNIX socket transport module.
[ 28.067452] RPC: Registered udp transport module.
[ 28.067458] RPC: Registered tcp transport module.
[ 28.067464] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 28.154405] FS-Cache: Loaded
[ 28.374995] FS-Cache: Netfs 'nfs' registered for caching
[ 28.759670] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
andrea@debian:~$

@ghillo

Quote:

During the boot I noticed two lines at the beginning that then do not appear if I run dmesg.

Check this:
https://amigaworld.net/modules/newbb/viewtopic.php?topic_id=42413&forum=34&start=20&viewmode=flat&order=0#808844

I think I may have solved your DMA problem. Check these lines out:
Quote:

[ 3.039177] ata1.00: ATA-8: WDC WD1600AVJB-63J5A0, 01.03E01, max UDMA/133 [ 3.039188] ata1.00: 312581808 sectors, multi 16: LBA48 [ 3.039212] ata1.01: ATAPI: HL-DT-ST GCE-8481B, 1.01, max UDMA/33 [ 3.039228] ata1.00: limited to UDMA/33 due to 40-wire cable [ 3.052801] ata1.00: configured for PIO4 [ 3.053342] ata1.01: configured for PIO4 ... [ 3.236325] ata2.00: ATA-5: MAXTOR 6L040J2, A93.0500, max UDMA/133 [ 3.236342] ata2.00: 78177792 sectors, multi 0: LBA [ 3.236365] ata2.01: ATAPI: TSSTcorp CDDVDW SH-S222A, SB02, max UDMA/66 [ 3.236381] ata2.00: limited to UDMA/33 due to 40-wire cable [ 3.236390] ata2.01: limited to UDMA/33 due to 40-wire cable [ 3.252313] ata2.00: configured for PIO4 [ 3.268106] ata2.01: configured for PIO4

Your IDE cables are too old. You need modern 80-wire cables for proper DMA. How are your drives configured? HD as master, CD as slave? Your setup is crippled. Also older cables tend to have devices in different connections. You could try to take the speed down a notch but it already detects the cable type so should be doing this itself. Best to replace your cables. Especially with a HD hanging off.

You could try adding this to enable SATA DMA but I can't test if it works. Keep the other option to disable all other DMA:
libata.force=sata.udma