Quote:

However, when I rebooted I still got the funky WB screen

What do you mean, white and blue ? Nothing there, not even a disk icon ? You have to re-attach your picasso settings, that's why it's not your usual screenmode.

_________________
Thomas, the kernel guy

"I don't have a frigging clue. I'm norwegian" -- Ole-Egil

All opinions expressed are my own and do not necessarily represent those of Hyperion Entertainment

F**K .-.-.
Had to use IE instead of Opera to get website working....
...btw. using Opera 8 for Windows.....

Everything ok now!

_________________
Amiga is the One...

Have fun!

_________________
- Ronald

All beer tastes bad.

@ EntilZha ..

Nope.

I've sorted it !!

phew, WHAT A headache

I noticed in the on screen blurb on switch on that Uboot was not listing the onboard ide dvdrw at all ?
( Well it works !!)

Only the hard drives which are on the Sil card.

So I grabbed an ide lead from box of spares and plugged cd (dvdrw) into secondary sil port.

Diskboot 500000 2:0

Success.

Reboot.

Bus 0 .........................................................................

no slb found blah blah blah.

Aaaaaaargh. (hang on, i recall people talking about this)

switch off and replug cd into onboard IDE while we're at it.

Finally get into Uboot (after much ado) and alter Multiboot options to Sil Paralell.

Success.




NOW for the update Os !!

_________________
******************************************
I dont suffer from Insanity - I enjoy it

******************************************

Quote:

However it wasn't clear to me and still isn't how to reattach the gc

Ahem, quoting from the README:

-- SNIP --
To re-attach the settings, start Picasso96Mode, press the menu button, and select your graphics card from the “Attach Settings To” menu. Save your settings afterwards, and reboot.
-- SNIP --

I think this is quite clear, isn't it?

_________________
Seriously, if you want to contact me do not bother sending me a PM here. Write me a mail

@ alef

Edit: Ok, just saw that you sorted this out. Thanks for the hint about Opera, that's the one browser we didn't test the site with...

Last edited by EntilZha on 14-Jun-2005 at 06:14 PM.

_________________
Thomas, the kernel guy

"I don't have a frigging clue. I'm norwegian" -- Ole-Egil

All opinions expressed are my own and do not necessarily represent those of Hyperion Entertainment

Does this update include hardware overlay for videoplayback?

Quote:

Does this update include hardware overlay for videoplayback?

For the Voodoo, yes. For the Radeon, no

_________________
Thomas, the kernel guy

"I don't have a frigging clue. I'm norwegian" -- Ole-Egil

All opinions expressed are my own and do not necessarily represent those of Hyperion Entertainment

How do I boot a CD that's connected to a Sil card again? I can't recall how I got this to work. I could connect it to an IDE port on the A1 mobo but I don't want to because I've had it booting before.

Cheers, FuZion.

(PS. I'm going to try ssolie's suggestion of a clean install)

Does anyone know if the new update will work with the Mobility Radeon 7500? (PCI ID 0x1002:0x4c57)? I have a 9800 I can use to install the new update, but I need to put it back in my PC so I can do my work...

Edit: The reason I'm asking is that that card will is not recognized by Pre2. This is the serial output from uboot:

Quote:

U-Boot 1.1.1 (Mar 3 2005 - 16:42:53), Build: 03/03/05 CPU: MPC7455 v2.1 @ 933.333 MHz Board: AmigaOne DRAM: Slot 0: vacant Information for SIMM bank 1: Number of banks: 1 Number of row addresses: 13 Number of coumns addresses: 11 SIMM is registered Supported burst lenghts: 8 4 2 1 PAGE Supported CAS latencies: CAS 3 RAS to CAS latency: 3 Precharge latency: 3 SDRAM highest CAS latency: 750 SDRAM 2nd highest CAS latency: 0 SDRAM data width: 4 Auto Refresh supported Refresh time: 1042 clocks Bank 0 size: 512 MB DIMM0_B0_SCR0 = 0x00000000 DIMM0_B1_SCR0 = 0x00000000 DIMM0_B2_SCR0 = 0x00ff9f00 DIMM0_B3_SCR0 = 0x00000000 Using CAS 3 (slow) DRAM_GCR0 = 0x00550400 Refresh set to 2083 clocks, auto refresh on DRAM_REFRESH0 = 0x00019823 Mode bank 2: 0x00008032 512 MB FLASH: 0 kB VGA: 0 .. In: serial Out: serial Err: serial [libInit] returning 0x018C1B40 [SetupInterrupts] which = 1, intNum = 28 , IRQ = 12 [SetupInterrupts] which = 0, intNum = 17 , IRQ = 1 AmigaOne.card/FindCard(): Entered Looking for Radeon 9500 Pro (0x1002:0x4144) Looking for Radeon 9700 Pro (0x1002:0x4145) Looking for Radeon 9700 Pro (0x1002:0x4146) Looking for Radeon 9800 (0x1002:0x4148) Looking for Radeon 9800 (0x1002:0x4149) Looking for Radeon 9600 Pro (0x1002:0x4150) Looking for Radeon 9600 Pro (0x1002:0x4151) Looking for Radeon 9600 (0x1002:0x4152) Looking for AIW 8500 DV (0x1002:0x4242) Looking for Radeon 9000 (0x1002:0x4964) Looking for Radeon 9000 (0x1002:0x4965) Looking for Radeon 9000 (0x1002:0x4966) Looking for Radeon 9000 (0x1002:0x4967) Looking for Radeon 9700 Pro (0x1002:0x4E44) Looking for Radeon 9700 Pro (0x1002:0x4E45) Looking for Radeon 9600 (0x1002:0x4E46) Looking for Radeon 9800 (0x1002:0x4E48) Looking for Radeon 9800 (0x1002:0x4E49) Looking for Radeon 9800 XT (0x1002:0x4E4A) Looking for Radeon 7200 (0x1002:0x5144) Looking for Radeon (0x1002:0x5145) Looking for Radeon (0x1002:0x5146) Looking for Radeon (0x1002:0x5147) Looking for Radeon 8500 (0x1002:0x5148) Looking for Radeon 8500 (0x1002:0x5149) Looking for Radeon 8500 (0x1002:0x514A) Looking for Radeon 8500 (0x1002:0x514B) Looking for Radeon 8500 LE (0x1002:0x514C) Looking for Radeon 9100 (0x1002:0x514D) Looking for Radeon 8500 LE (0x1002:0x514E) Looking for Radeon 8500 LE (0x1002:0x5148) Looking for Radeon 7500 (0x1002:0x5157) Looking for Radeon 7500 (0x1002:0x5158) Looking for Radeon 7000 (0x1002:0x5159) Looking for Radeon 7000 (0x1002:0x515A) Looking for Radeon 9200 (0x1002:0x5961) Looking for Radeon 9200 SE (0x1002:0x5964) Looking for Voodoo Banshee (0x121A:0x0003) Looking for Voodoo Avenger (0x121A:0x0005) Looking for Voodoo Rampage (0x121A:0x0009) AmigaOne.card/FindCard(): Exiting, returning 0 a1ide.device 51.29 (10.10.2004) [dev_init] ide_maxbus : '2', adjusted g_ide_maxunits to 4 [dev_init] Config not forced in $ide_conf, scanning IDE buses... [ide_list] Devices on IDE port 0 : [ide_list] Master : 'ATA' [ide_list] Slave : 'unknown type' [ide_list] Devices on IDE port 1 : [ide_list] Master : 'ATAPI' [ide_list] Slave : 'no device' [init_unit] Trying to configure unit 0 [ata_read_drive_properties] MultiCount 16 [ata_read_drive_properties] Adjusting unit 0 to xfer mode 12 [init_unit] Unit successfully configured, flags $0185 [init_unit] Trying to configure unit 1 [init_unit] Trying to configure unit 2 [ata_read_drive_properties] Adjusting unit 2 to xfer mode 12 [init_unit] Unit successfully configured, flags $0119 [init_unit] Trying to configure unit 3 si680ide.device 51.28 (07.10.2004) CMI8738 DriverInit CMI8738 found! ---> chiprev = 16, model = 111, Vendor = 13F6 INTERRUPT 26

And the ide for the card is

Quote:

] pci 1 Scanning PCI devices on bus 1 BusDevFun VendorId DeviceId Device Class Sub-Class _____________________________________________________________ 01.00.00 0x1002 0x4c57 Display controller 0x00 ]

Last edited by CodeSmith on 14-Jun-2005 at 06:34 PM.

Quite a pleasant surprise. I'd been under the impression that it was due out in the middle of "next" week, not this one.

Thanks to all developers and beta testers working on AOS4.

BTW, I've moved my dvd burner back to the Sil0680 card. It's seen by MediaToolBox, but even though I've edited the ToolTypes for DVD+RW and CDRW to DEVICE=sil0680ide.device and UNIT=3 (it's new location as a slave rather than master), it doesn't seem to mount.

I'll read through the entire discussion before I complain though. Probably something else I have to change that I haven't noticed.

Dave M.

Quote:

How do I boot a CD that's connected to a Sil card again? I can't recall how I got this to work. I could connect it to an IDE port on the A1 mobo but I don't want to because I've had it booting before.

In the boot options menu, select "Amiga Multiboot" (should already be selected), then go to "Amig Multiboot options" and select "SII parallel CDROM" or "SII serial CDROM", depending on whether you have the CDROM hooked to a ATA or SATA SII controller, respectively.

Then press ESC (until the main menu appears), and press ESC again, and select "Use settings for this session only".

Alternatively, when the progress bar appears, press ENTER and select the boot source directly (like above).

_________________
Thomas, the kernel guy

"I don't have a frigging clue. I'm norwegian" -- Ole-Egil

All opinions expressed are my own and do not necessarily represent those of Hyperion Entertainment

@amipal

Quote:

but I'm going to see "The Pacifier" aka Kintergarden Vin.

It's ok. My wife picked "The Titanic" out of the dvd cabinet. So you should not complain so much.

Coder

_________________
Can't get enough of me?
The Bucket Diary Blog
The Bucket Diary Twitter Account

Thanks Hyperion one step closer to buying my A1

_________________
4000T/BFG9060
CD32/Elsat ProModule, TF360
CD32/ Edu's CD32 <> A1200 Adapter, Vampire V2
CD32/ FMV Module

@EntilZha

Quote:

Poster: EntilZha Date: 14-Jun-2005 12:07:25 Quote: However, when I rebooted I still got the funky WB screen What do you mean, white and blue ? Nothing there, not even a disk icon ? You have to re-attach your picasso settings, that's why it's not your usual screenmode.

Ok, this is getting very frustrating. I've had to reinstall updates 1 and 3 a number of times now, and no matter which P96Mode and WBScreen settings I choose I get the WBScreen resolution I've choosen, but the WBScreen hangs at the point where it's blank before the icons and menu appears. No matter how long I wait the regular WB never appears. I'm now definitely out of clues as to what may be wrong.

_________________
--
-=#Val#=-
Valiant@Camelot


Amiga 1000; Amiga 2000; Amiga 3000T; CD-TV; CD32;
AmigaOne-XE 800Mhz G4;Sam400ep 666Mhz;
AmigaOne X-1000 1.8Ghz PA6T-1682M

I got a blank screen too...

I managed to sort it out by reinstalling from the CD doing a pre-release 3 but without chaning any of the scripts, still comes up looking 'orrible but at least you can change it back in prefs.

Not impressed to be honest, and less so in telling people to "RTFM" to fix the problems when they're sitting in fron of grey screen with nothing to change.

I've got it working now, but I couldn't imagine Microsoft making that big a coc, no hang on, yes I could.

_________________
Rage quited 29th May 2011

Quote:

No matter how long I wait the regular WB never appears. I'm now definitely out of clues as to what may be wrong.

So, the screen openes, but the workbench freezes at that time, no icons, nothing ?

We had a bug like this some time ago, but it was fixed. It was only happening on the Radeon and only when the prefs changed, i.e. you change GUI prefs, and the workbench closes. It wouldn't open anymore.

Did you do a complete re-install, i.e. clean the system disk, install from the CD, and then install update 3 ?

If yes, what hardware do you have in your machine (graphics card, sound card, ide controller) ?

Do you have the etherne in use ?

Also, please check if the MD5 sum matches that on the webpage... maybe the archive is somehow corrupted ?

Finally, please try to boot without startup sequence by pressing both mouse buttons or help on the keyboard (PS/2 only at the moment, sorry). If you can do that, disable WBStartup ("rename WBstartup WBStartup.off") and try again.

If you didn't do a complete re-install, make sure you don't have any old software in "unusual" places. For example, you might have dragged a commodity to wbstartup or similar.

If that still doesn't give a hint on your problem, please contact me in private mail (ThomasF@hyperion-entertainment.biz), that's easier than picking out your posts from here.

_________________
Thomas, the kernel guy

"I don't have a frigging clue. I'm norwegian" -- Ole-Egil

All opinions expressed are my own and do not necessarily represent those of Hyperion Entertainment

@ The AmigaOS4.0 Team

Thank you..

The machine does seem FASTER now.

One question though, when will the printing in AmiPDF work with TurboPrint again?

Cheers,
Tim

Quote:

Not impressed to be honest, and less so in telling people to "RTFM" to fix the problems when they're sitting in fron of grey screen with nothing to change.

You should RTFM _BEFORE_ isntalling the update. And sorry, we try our best to help you out when you have problems, but if you have problems because you didn't read the documentation, it's your fault.

Quote:

I've got it working now, but I couldn't imagine Microsoft making that big a coc, no hang on, yes I could.

What an inappropriate comparison.

_________________
Thomas, the kernel guy

"I don't have a frigging clue. I'm norwegian" -- Ole-Egil

All opinions expressed are my own and do not necessarily represent those of Hyperion Entertainment

Quote:

One question though, when will the printing in AmiPDF work with TurboPrint again?

It should already work.

Do you have a parallel printer, or USB ?

_________________
Thomas, the kernel guy

"I don't have a frigging clue. I'm norwegian" -- Ole-Egil

All opinions expressed are my own and do not necessarily represent those of Hyperion Entertainment